Most chimney leaks come from the flashing, the metal that seals the gap where the chimney meets the roof. The next most common causes are a missing cricket (a small peaked piece behind the chimney that splits the water), a cracked top on the chimney, a missing or rusted cap, and worn brick or mortar (the cement between the bricks). On many North Texas homes the chimney is a wood box covered in siding, and there the metal top and the siding seams are the usual weak spots. Watch where and when the water shows up, and it will point you to the cause.
Why chimneys leak so often
A chimney is a big box that sticks up through the roof. Rain runs down the slope and hits the high side of it. Water piles up there, then has to go around. Every side of the chimney is a seam, and seams are where water gets in. Hail, wind and hot summers wear on those seams, which is why so many leaks in Crowley, Fort Worth and Burleson start at the chimney.
Where the water gets in
- The flashing. A chimney needs a set of metal pieces on all four sides. Step flashing goes under each row of shingles along the sides. Counter flashing covers it and is set into the mortar lines on brick. When the metal rusts, pulls out of the mortar, or was never put in right, water runs behind it.
- No cricket. On a wide chimney, water and leaves pile up on the high side. A cricket is a small, peaked roof built behind the chimney that sends the water off to the sides. Without one, that spot stays wet and leaks.
- The crown. The crown is the cement slab on top of a brick chimney. It cracks in heat and the odd hard freeze. Water then soaks down into the brick.
- The cap. The cap is the cover over the flue (the pipe or opening the smoke goes up). A missing cap lets rain fall straight down the chimney. A rusted one can drip on the crown.
- Brick and mortar. Old mortar wears thin and cracks. Brick soaks up water, and in a long rain it can pass through to the inside.
- A wood chimney with siding. Many DFW homes have a chimney framed in wood and covered in siding, with a metal pan on top called a chase top. That pan can rust or hold water, and the siding seams can open up. Water then runs down inside the box.
How to tell where it is coming from
Do this from inside and from the yard. Please do not climb on the roof, and stay off it when it is wet.
- Look at when it leaks. Only in wind-driven rain from one side? That often points to the flashing or a siding seam on that side. In any steady rain? Think crown, cap or brick.
- Look at where the stain is. A stain on the ceiling next to the chimney, or on the wall beside the fireplace, often means flashing. Water inside the firebox (where you build the fire) or on the damper (the flap inside the flue) points to the cap or crown.
- Check the attic. With a flashlight, look at the wood around the chimney. Dark stains on the high side point to the cricket or the flashing up top. Stains low on one side point to the step flashing.
- Look from the yard. Look for metal that is bent, lifted or rusty, tar smeared around the base, leaves piled behind the chimney, cracked or crumbling mortar, and white crust on the brick, which means water has been moving through it.
Our post on ceiling water stains helps you trace a stain back to its source.
How each fix works
The fix should match the source. Here are the common ones.
- New flashing. The roofer lifts the shingles around the chimney, takes off the old metal, and sets new step and counter flashing. On brick, the counter flashing is cut into the mortar lines and sealed. This is the most common fix, and when done well it lasts. The trade-off: it does not help old, worn shingles nearby.
- Adding a cricket. On a wide chimney with none, a cricket is often added with the new flashing.
- Crown and cap work. A cracked crown can be sealed or rebuilt, and a cap can be added or replaced. This is often a job for a mason or chimney pro, not only a roofer.
- Brick and mortar repair. Worn mortar can be ground out and filled with new mortar. This is also mason work. A good roofer will tell you if the problem is the brick and not the roof.
- Wood chimneys. A rusted chase top can be replaced, and open siding seams can be sealed or the siding redone.
Be careful with a fix that is only more tar or caulk at the base. It may stop a drip for a while, but in Texas heat it cracks again and can hide the real problem. Our post on flashing and drip edge shows what good flashing should look like.
Chimneys and a new roof
If your roof is near the end of its life, the best time to fix chimney flashing is when the new roof goes on. The flashing should be new, not reused, and that is the time to add a cricket if the chimney needs one. When you get an estimate, ask:
- Will you replace the step and counter flashing, or reuse the old?
- Does my chimney need a cricket?
- What goes under the metal? A self-stick sheet around the chimney adds a second seal.
For coverage questions after a storm, ask your insurance agent.
What to do next
If your chimney leaks in Crowley, Fort Worth, Burleson, Mansfield, Joshua or a nearby town, see our roof repairs page or call Legacy Roofing at (817) 602-2057. To see the chimney and the whole roof first, set up a free drone roof survey. Someone needs to be home for the flight, and you see the pictures before we leave. You get a written photo report, and if something needs a closer look, it is checked by hand. We will tell you plainly what we see, and if the problem is the brick and not the roof, we will say so.



